Your location >> Index >> News
For the test clip
Time：2011-4-5 Hit：4328
Time：2011-4-5 Hit：4328
Button in the testing process has two main aspects:
One: is the pull test, this test is testing the capacity of clip, it is divided into two steps:
1, an instant pull test, mainly used for buckle, D buckle, buckle on the test when suddenly encountered strong pull, buckle strength.
2, persistent tension test, its main principle in determining the load of a certain weight, clip is exposed to time value.
3 buckle was also on the detection of frequency of use, keep the opening and closing, to test the number of times, the buckle will be deformed.
Three directions, the direction of the buckle or more detection more complex.
Second: is the temperature of the test, this is primarily to test clip in the unconventional temperature tolerance, is divided into two kinds of high temperature and low temperature
1, the temperature is usually set at 70 degrees Celsius
2, the temperature is usually set at minus 30 degrees. For 24 hours, and then test the strength of the change.
Third: is the salt spray test, this test is to monitor the main anti-Button salinity, some products can only be by sea transport, sea 長時間 run, have an impact on the quality of the product, the test has two steps .
1, the buckle on the 72-hour immersion in seawater
2, the clip on the sun soaked for 5-7 days following exposure
3, after completion of the test strength not changed much.
There are some anti-acid test, etc. For example, according to different needs and material to the corresponding values were detected, of which the metal clip on it but also rust and corrosion, such as drug resistance testing, the plastic buckle If the product with post processing, such as electroplating, water pollution, oil wiping process, but also to further test whether the eligibility criteria for these additional procedures.
Of course, the higher the standard test applied to the top diving and other extreme sports, what UL certification, TS16949 certification, VDA6.0 standards, manufacturers can not generally adopted by the clip. The above is a clip of the shallow state, with the continuous development of products, varieties increasingly diversified, this is more and more strict testing.
One: is the pull test, this test is testing the capacity of clip, it is divided into two steps:
1, an instant pull test, mainly used for buckle, D buckle, buckle on the test when suddenly encountered strong pull, buckle strength.
2, persistent tension test, its main principle in determining the load of a certain weight, clip is exposed to time value.
3 buckle was also on the detection of frequency of use, keep the opening and closing, to test the number of times, the buckle will be deformed.
Three directions, the direction of the buckle or more detection more complex.
Second: is the temperature of the test, this is primarily to test clip in the unconventional temperature tolerance, is divided into two kinds of high temperature and low temperature
1, the temperature is usually set at 70 degrees Celsius
2, the temperature is usually set at minus 30 degrees. For 24 hours, and then test the strength of the change.
Third: is the salt spray test, this test is to monitor the main anti-Button salinity, some products can only be by sea transport, sea 長時間 run, have an impact on the quality of the product, the test has two steps .
1, the buckle on the 72-hour immersion in seawater
2, the clip on the sun soaked for 5-7 days following exposure
3, after completion of the test strength not changed much.
There are some anti-acid test, etc. For example, according to different needs and material to the corresponding values were detected, of which the metal clip on it but also rust and corrosion, such as drug resistance testing, the plastic buckle If the product with post processing, such as electroplating, water pollution, oil wiping process, but also to further test whether the eligibility criteria for these additional procedures.
Of course, the higher the standard test applied to the top diving and other extreme sports, what UL certification, TS16949 certification, VDA6.0 standards, manufacturers can not generally adopted by the clip. The above is a clip of the shallow state, with the continuous development of products, varieties increasingly diversified, this is more and more strict testing.
2016 Copyright: Zhongshan City, Jimei handbags Accessories Co., Ltd.
